CONTROLLER> HELP

================================================================
              Controller(h) Help Information
              FW Version: 2.03.27

/*Help And Status Commands*/
?/HELP: Print help information.
GET STATUS: Get all status.

/*Commands For System Control*/
SET IR ON/OFF : Set controller IR control on or off.
SET RS232BAUDRATE [a] : Set RS-232 baud rate to a bps.
              a=[0:115200 1:57600, 2:38400, 3:19200, 4:9600]
SET RESET : Reset controller system settings.
SET RESET NETWORK : Reset controller network settings.
SET RESET ALL : Reset controller system and network settings.
              (Type "Yes" to confirm, "No" to cancle).

/*Commands For Encoder And Decoder Control*/
SET ENC PRESET IPMODE [mode] : Preset encoder ip mode.
SET ENC PRESET START IP [ip] : Preset encoder start ip address.
SET ENC PRESET END IP [ip] : Preset encoder end ip address.
SET ENC PRESET GW [gw] : Preset encoder gateway address.
SET ENC PRESET SM [mask] : Preset encoder subnet mask address.
SET ENC PRESET APPLY : Apply the encoder preset ip configuration.
SET ENC [enc] IPMODE DHCP/STATIC : Set the encoder ip mode.
SET ENC [enc] STATIC IP [ip] : Set the encoder static ip address.
SET ENC [enc] STATIC GATEWAY [gw] : Set the encoder static gateway address.
SET ENC [enc] STATIC MASK [mask] : Set the encoder static subnet mask address.
SET ENC [enc] NETWORK REBOOT : Set the encoder network reboot.
SET ENC [enc] ID [id] : Set the index ID of the encoder.
SET ENC [enc] DELETE : Delete the encoder in the current configuration.
SET ENC [enc] REBOOT : Set the encoder reboot.
SET ENC [enc] RESET : Set the encoder factory reset.
SET ENC [enc] AUDIO INPUT HDMI/ANA : Set the encoder audio input HDMI or embedded analogue L/R.
SET ENC [enc] NAME [name] : Set the name of the encoder.
SET ENC [enc] LED ON/OFF : Set the encoder flash power LED or disable flash power LED.
SET ENC [enc] LED ON 90 : Set the encoder flash power LED timeout in 90 seconds.
SET ENC [enc] FPLED [fl] : Set the encoder front panel LED automatic off time.
SET ENC [enc] GUEST ON/OFF BR [br] BIT [bit] : Set the encoder serial guest configuration.
              Note: To close guest mode use command EXITGUEST
SET ENC [enc] GUEST : Start serial guest mode to encoder enc
              Note: To close guest mode use command EXITGUEST
SET ENC [enc] IR VOL 5V/12V : Set the encoder IR voltage 5V or 12V.
SET ENC [enc] STREAM BITRATE [rate] : Set the encoder stream encoding bitrate.
SET ENC [enc] MAINSTREAM E [type] A ON/OFF: Set the encoder main stream attributation.
SET ENC [enc] SUBSTREAM E [type] H [sh] V [sv] B [rate] A ON/OFF: Set the encoder sub stream attributation.
SET ENC [enc] AUDIO FORMAT PCM/AAC : Set the encoder audio encoding format PCM or AAC.
SET ENC [enc] EDID COPY [dec] : Set the encoder EDID copy from decoder.
SET ENC [enc] EDID DEFAULT [edid] : Set the encoder default EDID.
GET ENC [enc] STATUS : Get the encoder Status.
SET DEC PRESET IPMODE [mode] : Preset decoder ip mode.
SET DEC PRESET START IP [ip] : Preset decoder start ip address.
SET DEC PRESET END IP [ip] : Preset decoder end ip address.
SET DEC PRESET GW [gw] : Preset decoder gateway address.
SET DEC PRESET SM [mask] : Preset decoder subnet mask address.
SET DEC PRESET APPLY : Apply the decoder preset ip configuration.
SET DEC [dec] OUTPUT ON/OFF : Set the decoder output on or off.
SET DEC [dec] IPMODE DHCP/STATIC : Set the decoder static ip mode.
SET DEC [dec] STATIC IP [ip] : Set the decoder static ip address.
SET DEC [dec] STATIC GATEWAY [gw] : Set the decoder static gateway address.
SET DEC [dec] STATIC MASK [mask] : Set the decoder static subnet mask address.
SET DEC [dec] NETWORK REBOOT : Set the decoder network reboot.
SET DEC [dec] ID [id] : Set the index ID of the decoder.
SET DEC [dec] SWITCH [enc] ALL : Set the decoder switch all signals.
              Note: enc=0 mean no source in this case
SET DEC [dec] SWITCH [enc] VIDEO : Set the decoder switch video only signals.
SET DEC [dec] SWITCH [enc] RS232 : Set the decoder switch RS232 only signals.
SET DEC [dec] SWITCH [enc] IR : Set the decoder switch IR only signals.
SET DEC [dec] SWITCH [enc] USB : Set the decoder switch USB only signals.
SET DEC [dec] OUTPUT OSD ON/OFF : Set the decoder output to show ID OSD or hide ID OSD.
SET DEC [dec] OUTPUT OSD ON 90 : Set the decoder output show ID OSD timeout in 90 seconds.
SET DEC [dec] LED ON/OFF : Set the decoder flash power LED or disable flash power LED.
SET DEC [dec] LED ON 90 : Set the decoder flash power LED timeout in 90 seconds.
SET DEC [dec] DELETE : Delete the decoder in the current configuration.
SET DEC [dec] OUTPUT RESOLUTION [res] : Set the decoder output resolution.
SET DEC [dec] OUTPUT ROTATE [rtt] : Set the decoder output rotate.
SET DEC [dec] NAME [name] : Set the name of the decoder.
SET DEC [dec] MODE MX/VW : Set the decoder output mode to matrix or video wall.
SET DEC [dec] BUTTON ON/OFF : Set the decoder front panel button enable on or off.
SET DEC [dec] IR ON/OFF : Set the decoder rear panel IR enable on or off.
SET DEC [dec] IR VOL 5V/12V : Set the decoder IR voltage 5V or 12V.
SET DEC [dec] OUTPUT PAUSE ON/OFF : Set the decoder output pause on or off.
SET DEC [dec] OUTPUT MUTE ON/OFF : Set the decoder output mute on or off.
SET DEC [dec] OUTPUT AUTO ON/OFF : Set the decoder output automatically on or off.
SET DEC [dec] FPLED [fl] : Set the decoder front panel LED automatic off time.
SET DEC [dec] GUEST ON/OFF BR [br] BIT [bit] : Set the decoder serial guest configuration.
SET DEC [dec] GUEST : Start serial guest mode to decoder dec
              Note: To close guest mode use command EXITGUEST
SET DEC [dec] STREAM UNICAST/MULTICAST : Set the decoder output stream transmission mode UNICAST or MULTICAST.
SET DEC [dec] OUTPUT LOST [time] : Set the decoder output video lost timeout in minute.
GET DEC [dec] STATUS : Get the decoder status.
SET DEC [dec] REBOOT : Set the decoder reboot.
SET DEC [dec] RESET : Set the decoder factory reset.
EXITGUEST : Exit encoder or decoder guest mode.
SET DEC [dec] HOTKEY [nn] KEY [k0] [k1] ACTION PULL/PUSH SRC [enc] : Set the decoder hotkey config.
SET DEC [dec] HOTKEY [nn] DEL : Delete the decoder hotkey config.
              dec=0: All decoder
              dec=[1...762]: One decoder
              enc=0: All encoder
              enc=[1...762]: One encoder
              id=[1...762]
              rate=[0:1Mb 1:4Mb 2:8Mb 3:16Mb 4:20Mb]
              edid=[00: HDMI 1080p@60Hz, Audio 2CH PCM
                    01: HDMI 720p@60Hz, Audio 2CH PCM
                    02: DVI 1280x1024@60Hz, Audio None
                    03: DVI 1920x1080@60Hz, Audio None
                    04: DVI 1920x1200@60Hz, Audio None
                    05: HDMI 1920x1200p@60Hz, Audio 2CH PCM
                    06: Copy EDID 
                    07: User EDID 1
                    08: User EDID 2]
              res=[0:Bypass 1:1080p@60 2:1080p@50 3:1080p@30 4:1080p@25 5:1080p@24]
                  [6:720@p60 7:720p@50 8:576p@50 9:480p@60]
                  [10:640x480@60 11:800x600@60 12:1024x768@60 13:1280x800@60]
                  [14:1280x1024@60 15:1366x768@60 16:1440x900@60 17:1600x1200@60]
                  [18:1680x1050@60 19:1920x1200@60]
              rtt=[0:0 1:90 2:180 3:270]
              mode=[0:AUTOIP 1:DHCP 2:STATIC]
              br=[0:300 1:600 2:1200 3:2400 4:4800 5:9600]
                 [6:19200 7:38400 8:57600 9:115200]
              bit=Data bits + parity + stop bits, example: 8n1
              Data bits=[5...8], parity=[n o e], stop bits=[1..2]
              ip=[xxx.xxx.xxx.xxx]
              name: Max 16 characters
              fl: [0: Always On  9: On 90s]
              time[0...60]: Unit minute
              gw=[xxx.xxx.xxx.xxx]
              mask=[xxx.xxx.xxx.xxx]
              type=[0:h264 1:h265]: Encode type
              sh=[320...640]: Sub stream encode horizontal value(must be even number)
              sv=[180...540]: Sub stream encode vertical value(must be even number)
              nn=[1...20]: Hotkey number
              k0=01: Left Ctrl
              k0=02: Right Ctrl
              k0=03: Left Shift
              k0=04: Right Shift
              k0=05: Left Alt
              k0=06: Right Alt
              k0=07: Ctrl Shift
              k0=08: Ctrl Alt
              k0=09: Shift Alt
              k1=ASCII code

/*Commands For Video Wall Control*/
CREATE WALL HANDLE [hdl] : Create video wall.
DELETE WALL HANDLE [hdl] : Delete video wall.
SET WALL [hdl] NAME [name] : Set the video wall name.
SET WALL [hdl] C [c] R [r] : Set the video wall columns and rows .
SET WALL [hdl] DEC [dec] H [h] V [v] : Set the video wall position (h,v) decoder.
CREATE WALL [hdl] PRESET [prs] : Create video wall preset.
DELETE WALL [hdl] PRESET [prs] : Delete video wall preset.
SET WALL [hdl] PRESET [prs] NAME [name] : Set the video wall preset name.
APPLY WALL [hdl] PRESET [prs] : Apply video wall preset.
SET WALL [hdl] PRESET [prs] CLASS [cls] H [h] V [v] : Set the video wall preset  position (H,V) as class.
SET WALL [hdl] PRESET [prs] CLASS [cls] SOURCE [enc] : Set the video wall preset class from the source.
SET WALL [hdl] PRESET [prs] MATRIX H [h] V [v] : Set the video wall preset to specify the location as a matrix mode.
SET WALL [hdl] PRESET [prs] MATRIX H [h] V [v] SOURCE [enc] : Set the video wall preset class from the source.
SET WALL [hdl] H [h] V [v] WIDTH BEZEL BW [o] IW [w] : Set the video wall position (h,v) base width and image width.
SET WALL [hdl] H [h] V [v] HEIGHT BEZEL BH [o] IH [w] : Set the video wall position (h,v) base height and image height.
GET WALL [hdl] STATUS : Get the video wall status.
              hdl=[01...09]: Video wall handle
              prs=[01...09]: Preset index
              cls=[A...G]:   Class index
              c=[01...09]: Number of columns in video wall
              r=[01...09]: Number of rows in video wall
              h=[01...09]: Horizontal position in video wall
              v=[01...09]: Vertical position in video wall
              o=[100...1000]: Screen base width/height
              w=[100...1000]: Screen image width/height
              enc=[001...n]: One encoder
              enc=000: No source
              dec=000: Remove decoder from position
              dec=[001...n]: One decoder
              name: Max 16 characters

/*Commands For Device Management*/
SEARCH : Search all encoders and decoders.
GET SEARCH STATUS : Get the search status.
SEARCH RESET : Reset search encoders and decoders.
ADD DEV [dev] ENC [enc] : Add new encoder devices.
ADD DEV [dev] DEC [dec] : Add new decoder devices.
ADD DEV RESET : Reset all encoder/decoder/videowall/search configurations.
ADD AUTO ALL : Automatically add encoders and decoders for all new searches.
              dev=[01...n]:  Search list index value
              enc=[001...n]: One encoder
              dec=[001...n]: One decoder

/*Commands For GPIO Control*/
SET GPIO [gpio] DIR IN/OUT : Set the controller gpio as input or output.
SET GPIO [gpio] LEVEL Low/High : Set the controller gpio output low level or high level.
GET GPIO [gpio] LEVEL : Get the controller gpio input level.
GET GPIO [gpio] STATUS : Get the controller gpio status.
              gpio=00: All IO ports
              gpio=[01...04]: One IO port

/*Commands For Network Control*/
SET NETWORK [lan] DHCP ON/OFF : Set the controller network dhcp on or off.
SET NETWORK [lan] STATIC IP [ip] : Set the controller network static ip address.
SET NETWORK [lan] STATIC GATEWAY [gw] : Set the controller network static gateway address.
SET NETWORK [lan] STATIC MASK [mask] : Set the controller network static subnet mask address.
SET NETWORK REBOOT : Set the controller network reboot.
SET NETWORK TELNET ON/OFF : Set the controller network telnet on or off.
SET NETWORK TELNET PORT [port] : Set the controller network telnet port.
SET NETWORK SSH ON/OFF : Set the controller network ssh on or off.
SET NETWORK SSH PORT [port] : Set the controller network ssh port.
SET NETWORK HTTPS ON/OFF : Set the controller network https on or off.
SET NETWORK WEB ON/OFF : Set the controlller network web GUI on or off.
SET NETWORK DNS hostname : Set the controller network domain name to hostname.
              lan=LAN1: Video LAN(POE)
              lan=LAN2: Control LAN(Web GUI)
              ip=[xxx.xxx.xxx.xxx]
              gw=[xxx.xxx.xxx.xxx]
              mask=[xxx.xxx.xxx.xxx]
              port=[22...65535]
================================================================